Effects of cross-sectional shape on the bending strength in furniture joints
Yıl: 2018 Cilt: 18 Sayı: 2 Sayfa Aralığı: 164 - 170 Metin Dili: İngilizce DOI: 10.17475/kastorman.342070 İndeks Tarihi: 13-09-2019
Effects of cross-sectional shape on the bending strength in furniture joints
Öz: Aim of the study: Tests were carried out to evaluate the ultimate bending strength of the circular and square cross sectioned furniture joint members and find out whether the form factor is applicable to the small specimens as they are applied to large specimens and compare the maximum bending strength and specific gravity values of these wood species to those that are specified in reference books.Material and methods: The specimens were prepared from Red oak (Quercus rubra), Yellow poplar (Liriodendron tulipifera), Southern pine (Pinus sp.), Caobilla (Carapa guianensis), and Gmelina (Gmelina arborea). Based on five wood species by five replications, 25 square cross sectional (25 x 25mm)specimens and 25 specimens which included 19 mm diameter circular mortise and tenon joints, a total of 50 specimens were prepared and tested under the static bending test according to related standards.Main results: Results gave the primary indication that the form factor of 1.18 from square to circular cross section is applicable to small clear specimens; however, it should be noted that absolute conclusions require studies in much wider spectrum.Research highlights: The results of this study indicate that designers and furniture engineers may obtain good estimates from 1.18 form factor and comparison of MOR values and specific gravity of the wood species with the book values.
Anahtar Kelime: Konular:
Yuvarlak ve kare kesitli mobilya bağlantı elemanlarının eğilme direncinin karşılaştırılması
Öz: Çalışmanın amacı: Bu çalışma, dairesel ve kare kesitli mobilya bağlantı elemanlarının maksimum eğilme mukavemetinin değerlendirilmesi ve küçük test örneklerine uygulanan şekil faktörünün büyük test örneklerine uygulandığında uygulanabilirliğinin değerlendirilmesi ve kullanılan ağaç türlerine ilişkin maksimum eğilme mukavemeti ve özgül ağırlık değerlerinin referans kitaplarda verilen değerler ile karşılaştırılması amaçlanmıştır. Materyal ve Metot: Test örneklerinin hazırlanmasında kızıl meşe (Quercus rubra), sarı kavak (Liriodendron tulipifera), çam (Pinus sp .), caobilla (Carapa guianensis), and gmelina (Gmelina arborea) ağaç türleri kullanılmıştır. Beş ağaç türü ve beş tekrardan oluşan toplam 25 kare kesitli (25x25 mm) ve 19 mm çapında yuvarlak zıvana bağlantısı uygulanan diğer 25 test örneği olmak üzere toplam 50 test örneği ilgili standartlara göre statik yük altında test edilmiştir. Sonuçlar: Sonuçlar göstermiştir ki köşeli kesitten yuvarlak kesite 1.18 katsayısı kullanılarak küçük test örneklerine uygulama yapılabilir ancak belirtmek gerekir ki kesin sonuçlar için daha geniş kapsamlı çalışmalara ihtiyaç duyulmaktadır. Önemli vurgular: Bu çalışmanın bir sonucu olan 1.18 katsayısının ve ayrıca özgül ağırlık ve eğilme direnci değerlerinin referans kitap değerleri ile karşılaştırma sonuçlarının, mobilya mühendisleri ve tasarımcıları tarafından tasarım süreçlerinde kullanılabileceği söylenebilir.
Anahtar Kelime: Konular:
Belge Türü: Makale Makale Türü: Araştırma Makalesi Erişim Türü: Erişime Açık
- Addis, T., Buchanan, A.H., Walker, J.C.F., (1995). A comparison of density and stiffness for predicting wood quality or density: The lazy man's guide to wood quality. Journal of the Institute of Wood Science, 13(6), 539-543.
- ASTM D 143-94, (2000). Standard methods for testing small clear specimens of timber. American Society for Testing and Materials, West Conshohocken, PA.
- ASTM D 4442-92, (2001). Standard methods for testing for direct moisture content measurement of wood and wood-base materials. American Society for Testing and Materials, West Conshohocken, PA.
- Chudnoff, M., (1984). Tropical Timbers of the World. Agricultural Handbook No.607, Madison WI: U.S. Department of Agriculture, Forest Service, Forest Products Laboratory. 464 pp.
- Cown. D.J., (1992). Corewood (Juvenile Wood) in Pinus radiate - should we be concerned? New Zealand J. Forestry Sci. 22(1), 87-95.
- Dinwoodie, J.M., (2000). Timber - Its Nature and Behavior. E & FN Spon, Taylor & Francis Group, London and New York.
- Eckelman, C.A., Erdil, Y.Z., Haviarova, E., (2002). Effect of Cross Holes on the Strength of Chair and Table Legs. Forest Product journals, 52(5), 67-70.
- Efe, H., Zhang, J., Erdil, Y.Z., Kasal, A., (2005). Moment Capacity of Traditional and Alternative T-Type End-to-Side-Grain Furniture Joints. Forest Products Journal, 55(5), 69-73.
- Erdil, Y.Z., Kasal, A., (2005). Bending Moment Capacity of Rectangular Mortise and Tenon Furniture Joints. Forest Products Journal 55(12), 209-213.
- Harvald, C., Olesen, P.O., (1987). The variation of the basic density within the juvenile wood of Sitka spruce (Piceasitchensis). Scand. J. Forest Res. 2, 525-537.
- Markwardt L.J., Wilson, T.R.C., (1935). Strength and Related Properties of Woods Grown in The United States: Technical Bulletin No: 479. U.S. Department of Agriculture, Forest Service, Forest Products Laboratory, 99 pp.
- Newlin, J., Trayer, G., (1924). Form Factors of Beams Subjected to Transverse Loading, Rep. 181 to Nat. Advisory Committee for Aeronautics, Reprinted 1941 as Rep. 1310, Madison, WI: US. Department of Agriculture, Forest service Forest Products Laboratory.
- Philips, E.W.J., (1941). The inclination of the fibrils in the cell wall and its relation to the compression strength of timber. Empire Forestry J. 20, 74-78.
- Schniewind, A.P., (1989). Concise encyclopaedia of wood and wood-based materials. Pergamon Press. pp: 248. Gen. Tech. Rept. FPL-GTR-113, (1999). Wood Handbook: Wood as an Engineering Material. USDA Forest Serv., Forest Prod. Lab., Madison, WI. 463 pp.
- Wolfe, R., Bodig, J., Lebow P., (2001). Derivation of Nominal Strength for Wood Utility Poles, Gen. Tech. Rep. FPL-GTR-128, Madison WI: U.S. Department of Agriculture, Forest Service, Forest Products Laboratory, 11 pp.
- Walker, J.C.F., Butterfield, B.G., (1996). The importance of the microfibril angle for the processing industries. New Zealand Forestry, 40(3), 34-40.
| APA | Acar M, DILER H, ERDIL Y (2018). Effects of cross-sectional shape on the bending strength in furniture joints. , 164 - 170. 10.17475/kastorman.342070 |
| Chicago | Acar Mehmet,DILER HARUN,ERDIL YUSUF ZIYA Effects of cross-sectional shape on the bending strength in furniture joints. (2018): 164 - 170. 10.17475/kastorman.342070 |
| MLA | Acar Mehmet,DILER HARUN,ERDIL YUSUF ZIYA Effects of cross-sectional shape on the bending strength in furniture joints. , 2018, ss.164 - 170. 10.17475/kastorman.342070 |
| AMA | Acar M,DILER H,ERDIL Y Effects of cross-sectional shape on the bending strength in furniture joints. . 2018; 164 - 170. 10.17475/kastorman.342070 |
| Vancouver | Acar M,DILER H,ERDIL Y Effects of cross-sectional shape on the bending strength in furniture joints. . 2018; 164 - 170. 10.17475/kastorman.342070 |
| IEEE | Acar M,DILER H,ERDIL Y "Effects of cross-sectional shape on the bending strength in furniture joints." , ss.164 - 170, 2018. 10.17475/kastorman.342070 |
| ISNAD | Acar, Mehmet vd. "Effects of cross-sectional shape on the bending strength in furniture joints". (2018), 164-170. https://doi.org/10.17475/kastorman.342070 |
| APA | Acar M, DILER H, ERDIL Y (2018). Effects of cross-sectional shape on the bending strength in furniture joints. Kastamonu Üniversitesi Orman Fakültesi Dergisi, 18(2), 164 - 170. 10.17475/kastorman.342070 |
| Chicago | Acar Mehmet,DILER HARUN,ERDIL YUSUF ZIYA Effects of cross-sectional shape on the bending strength in furniture joints. Kastamonu Üniversitesi Orman Fakültesi Dergisi 18, no.2 (2018): 164 - 170. 10.17475/kastorman.342070 |
| MLA | Acar Mehmet,DILER HARUN,ERDIL YUSUF ZIYA Effects of cross-sectional shape on the bending strength in furniture joints. Kastamonu Üniversitesi Orman Fakültesi Dergisi, vol.18, no.2, 2018, ss.164 - 170. 10.17475/kastorman.342070 |
| AMA | Acar M,DILER H,ERDIL Y Effects of cross-sectional shape on the bending strength in furniture joints. Kastamonu Üniversitesi Orman Fakültesi Dergisi. 2018; 18(2): 164 - 170. 10.17475/kastorman.342070 |
| Vancouver | Acar M,DILER H,ERDIL Y Effects of cross-sectional shape on the bending strength in furniture joints. Kastamonu Üniversitesi Orman Fakültesi Dergisi. 2018; 18(2): 164 - 170. 10.17475/kastorman.342070 |
| IEEE | Acar M,DILER H,ERDIL Y "Effects of cross-sectional shape on the bending strength in furniture joints." Kastamonu Üniversitesi Orman Fakültesi Dergisi, 18, ss.164 - 170, 2018. 10.17475/kastorman.342070 |
| ISNAD | Acar, Mehmet vd. "Effects of cross-sectional shape on the bending strength in furniture joints". Kastamonu Üniversitesi Orman Fakültesi Dergisi 18/2 (2018), 164-170. https://doi.org/10.17475/kastorman.342070 |
