Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD)

Oğuz ERDEM, (Kırşehir Ahi Evran Üniversitesi)
Can ÇOĞUN, (Çankaya Üniversitesi)
İBRAHİM USLAN (Gazi Üniversitesi)
International journal of advances in engineering and pure sciences (Online)
1 1
Yıl: 2019 Cilt: 31 Sayı: 1 Sayfa Aralığı: 11 - 16 Metin Dili: İngilizce DOI: 10.7240/jeps.450866 İndeks Tarihi: 05-04-2020

Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD)

Öz:
In electric discharge drilling (EDD), rapid local heating and cooling of the workpiece surface by means of electric discharges results insurface layers (recast, heat affected and base material). In this study, the main workpiece surface texture measures, namely the recast layerthickness (RLT) and average surface roughness (Ra) characteristics were investigated for varying machining parameters (discharge currentand pulse on time). The conducted experiments revealed the strong dependence of surface characteristics on machining parameters.
Anahtar Kelime:

Elektro Erozyon ile Delik Delmede İşlemenin İşparçası Yüzey Karakteristiklerine Etkisi

Öz:
Elektro erozyon ile delik delmede (EEDD), işparçası yüzeyinin elektriksel boşalmalar yoluyla hızlı bir şekilde bölgesel olarak ısıtılması ve soğutulması, yüzey katmanlarına (tekrardan katılaşmış, ısıl etkilenmiş ve ana malzeme) neden olur. Bu çalışmada, ana işparçası yüzey dokusu, yani tekrardan katılaşmış katman kalınlığı (RLT) ve ortalama yüzey pürüzlülüğü (Ra) özellikleri, farklı işleme parametreleri için (boşalım akımı ve vurum süresi) araştırılmıştır. Yapılan deneyler, yüzey özelliklerinin işleme parametrelerine kuvvetle bağımlılığını ortaya koymuştur.
Anahtar Kelime:

Belge Türü: Makale Makale Türü: Araştırma Makalesi Erişim Türü: Erişime Açık
  • [1] Gülcan, O., Uslan, İ., Usta, Y., & Çoğun, C. (2015). Elektro Erozyon ile İşlemede Cu-Cr T/M Elektrot Kullanımının İşleme Performansına Etkisi. Journal of the Faculty of Engineering and Architecture of Gazi University, 30(3), 381-394.
  • [2] Klocke, F., Schneider, S., Ehle, L., Meyer, H., Hensgen, L., and Klink, A. (2016). Investigations on Surface Integrity of Heat Treated 42CrMo4 (AISI 4140) Processed by Sinking EDM. Procedia CIRP, 42(2), 580-585.
  • [3] Li, J., Shi, S., & Zhao, S. (2013). Modeling and Analysis of Micro-hole in Die-sinking EDM Process through Response Surface Method based on the Central Composite Design. International Journal of Signal Processing, Image Processing and Pattern Recognition, 6(6), 351-364.
  • [4] Yılmaz, O., Bozdana, A. T., & Okka, M. A. (2014). An intelligent and automated system for electrical discharge drilling of aerospace alloys: Inconel 718 and Ti-6Al-4V. Int. J. Adv. Manuf. Technol, 74(9), 1323-1336.
  • [5] Bozdana, A. T., & Al-Karkhi, N. K. (2017). Comparative experimental investigation and gap flow simulation in electrical discharge drilling using new electrode geometry. Mechanical Sciences, 8(2), 289–298.
  • [6] D’Urso, G., Maccarini, G., Quarto, M., Ravasio, C., & Caldara, M. (2016). Micro-electro discharge machining drilling of stainless steel with copper electrode: The influence of process parameters and electrode size. Advances in Mechanical Engineering, 8(12), 1-16.
  • [7] Unses, E., & Cogun, C. (2015). Improvement of Electric Discharge Machining (EDM) Performance of Ti-6Al-4V Alloy with Added Graphite Powder to Dielectric. Strojniški vestnik – Journal of Mechanical Engineering, 61(6), 409-418.
  • [8] Newton, T. R., Melkote, S. N., Watkins, T. R., Trejo, R. M., & Reister, L. (2009). Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718. Materials Science and Engineering A – Structrual Materials Properties, 5(4), 208-215.
  • [9] Chen, S. L., Lin, M. H., Huang, G. X., & Wang, C. C. (2014). Research of the recast layer on implant surface modified by micro-current electrical discharge machining using deionized water mixed with titanium powder as dielectric solvent. Applied Surface Science, 31(1), 47-53.
  • [10] Shabgard, M. R., Seyedzavvar, M., & Oliaei, S. (2011). Influence of input parameters on characteristics of EDM process. Strojni˘ ski vestnik – J. Mech. Eng., 57(9), 689-696.
  • [11] Arooj, S., Shah, M., Sadiq, S., Jaffery, S. H. I., & Khushnood, S. (2014). Effect of Current in the EDM Machining of Aluminum 6061-T6 and its Effect on the Surface Morphology. Arab. J. Sci. Eng., 39(2), 4187-4199.
  • [12] Cogun, C., Esen, Z., Genc, A., Cogun F., & Akturk, N. (2016). Effect of powder metallurgy Cu-B4C electrodes on workpiece surface characteristics and machining performance of electric discharge machining. Proc. IMechE Part B: J. Engineering Manufacture, 230(12), 2190-2203.
  • [13] Amineh, S. K., Tehrani, A. F., & Mohammadi, A. (2013). Improving the surface quality in wire electrical discharge machined specimens by removing the recast layer using magnetic abrasive finishing method. Int. J. Adv. Manuf. Technol, 66(3), 1793-1803.
  • [14] Hasçalık, A., & Çaydaş, U. (2007). Electrical discharge machining of titanium alloy (Ti–6Al–4V). Applied Surface Science, 5(3), 9007-9016.
  • [15] Zhang, Y., Liu, Y., Ji, R., & Cai, B. (2011). Study of the recast layer of a surface machined by sinking electrical discharge machining using water-in-oil emulsion as dielectric. Applied Surface Science, 25(7), 5989-5997.
  • [16] Ramasawmy, H., Blunt, L., & Rajurkar, K. P. (2005). Investigation of the relationship between the white layer thickness and 3D surface texture parameters in the die sinking EDM process. Precision Engineering, 29(3), 479-490.
  • [17] Banu, A., Ali, M. Y., & Rahman, M. A. (2014). Micro-electro discharge machining of non-conductive zirconia ceramic: investigation of MRR and recast layer hardness. Int. J. Adv. Manuf. Technol., 75(2), 257-267.
  • [18] Ruellan, A., Kleber, X., Ville, F., Cavoret, J., & Liatard, B. (2001). Understanding white etching cracks in rolling element bearings: Formation mechanisms and influent tribochemical drivers. The Proceedings of the Institution of Mechanical Engineers, Part B, Journal of Engineering Manufacture, 229(8), 886-901.
  • [19] Nagaoka, A., Yokoyama, K., & Sakai, J. (2010). Evaluation of hydrogen absorption behaviour during acid etching for surface modification of commercial pure Ti, Ti–6Al–4V and Ni– Ti superelastic alloys. Corrosion Science, 52(3), 1130-1138.
  • [20] Ay, M., Hasçalık, A., & Çaydaş, U. (2012). Yüksek Toleranslı Plazma Arkı İle Kesme Parametrelerinin Araştırılması. 3. Ulusal Talaşlı İmalat Sempozyumu, Ankara, Türkiye, 04-05 Ekim. Gazi Üniversitesi Teknoloji Fakültesi.
APA ERDEM O, Çoğun C, USLAN İ (2019). Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). , 11 - 16. 10.7240/jeps.450866
Chicago ERDEM OGUZ,Çoğun Can,USLAN İBRAHİM Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). (2019): 11 - 16. 10.7240/jeps.450866
MLA ERDEM OGUZ,Çoğun Can,USLAN İBRAHİM Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). , 2019, ss.11 - 16. 10.7240/jeps.450866
AMA ERDEM O,Çoğun C,USLAN İ Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). . 2019; 11 - 16. 10.7240/jeps.450866
Vancouver ERDEM O,Çoğun C,USLAN İ Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). . 2019; 11 - 16. 10.7240/jeps.450866
IEEE ERDEM O,Çoğun C,USLAN İ "Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD)." , ss.11 - 16, 2019. 10.7240/jeps.450866
ISNAD ERDEM, OGUZ vd. "Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD)". (2019), 11-16. https://doi.org/10.7240/jeps.450866
APA ERDEM O, Çoğun C, USLAN İ (2019). Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). International journal of advances in engineering and pure sciences (Online), 31(1), 11 - 16. 10.7240/jeps.450866
Chicago ERDEM OGUZ,Çoğun Can,USLAN İBRAHİM Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). International journal of advances in engineering and pure sciences (Online) 31, no.1 (2019): 11 - 16. 10.7240/jeps.450866
MLA ERDEM OGUZ,Çoğun Can,USLAN İBRAHİM Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). International journal of advances in engineering and pure sciences (Online), vol.31, no.1, 2019, ss.11 - 16. 10.7240/jeps.450866
AMA ERDEM O,Çoğun C,USLAN İ Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). International journal of advances in engineering and pure sciences (Online). 2019; 31(1): 11 - 16. 10.7240/jeps.450866
Vancouver ERDEM O,Çoğun C,USLAN İ Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). International journal of advances in engineering and pure sciences (Online). 2019; 31(1): 11 - 16. 10.7240/jeps.450866
IEEE ERDEM O,Çoğun C,USLAN İ "Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD)." International journal of advances in engineering and pure sciences (Online), 31, ss.11 - 16, 2019. 10.7240/jeps.450866
ISNAD ERDEM, OGUZ vd. "Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD)". International journal of advances in engineering and pure sciences (Online) 31/1 (2019), 11-16. https://doi.org/10.7240/jeps.450866
Sayfa Oluşturulma Tarihi
23-04-2024 11:7

İLETİŞİM

TÜBİTAK ULAKBİM TR Dizin

Yüzüncüyıl, İşçi Blokları Mahallesi

Muhsin Yazıcıoğlu Caddesi No:51/C

06530 Çankaya / ANKARA +90 (312) 298 92 00

trdizin@tubitak.gov.tr

TÜBİTAK ULAKBİM Ulusal Akademik Ağ ve Bilgi Merkezi Cahit Arf Bilgi Merkezi © Tüm Hakları Saklıdır. Gizlilik Politikası Kullanım Şartları