Yıl: 2021 Cilt: 26 Sayı: 2 Sayfa Aralığı: 401 - 420 Metin Dili: Türkçe DOI: 10.17482/uumfd.943314 İndeks Tarihi: 29-07-2022

ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ

Öz:
Direnç nokta kaynağı (DNK), otomotiv, beyaz eşya, mobilya ve sac işleme endüstrilerinde yaygınolarak kullanılmaktadır. Orta frekans doğru akım (OFDA) ise DNK kalitesini arttıran, yenilikçi biryöntemdir. Bu çalışmada, OFDA-DNK sistemlerinden kaynak akım bilgisini elde edebilen bir analogintegratör devre önerilmiştir. OFDA-DNK sisteminin kontrolü için ihtiyaç duyulan bu akım bilgisi,Rogowski bobininden (RB) elde edilmiştir. Kaynak transformatörünün sekonderine bağlanan RBüzerinden, kaynak akımı ile ilgili gerilim bilgisi alınmıştır. Daha sonra önerilen integratör devre yardımıylaanalog sayısal dönüştürücüye veri aktarımı gerçekleştirilmiştir. Önerilen devrenin başarımı, oluşturulanOFDA-DNK sisteminde test edilmiştir. Deneysel sonuçlara göre, önerilen devrenin yaklaşık 30 kA akımakadar gerilim dönüşümünü hatasız bir şekilde yapabildiği görülmüştür. Ayrıca, önerilen devre için, OFDADNK uygulamalarında analog sayısal dönüştürücüye (ASD) doğrusal akım ölçüm verisi gönderebilecekpotansiyele sahip olduğu söylenebilir.
Anahtar Kelime: İntegrator devre Orta frekans doğru akım Direnç nokta kaynağı Rogowski bobini

Design and Implementation of a Current Measurement Circuit for Medium Frequency Direct Current Resistance Spot Welding Systems

Öz:
Resistance spot welding (RSW) is widely used in the automotive, white goods, furniture and sheet metal processing industries. Medium frequency direct current (MFDC) is an innovative method that increases the quality of RSW. In this study, an analog integrator circuit that can obtain the welding current information from MFDC-RSW systems is proposed. This current information required for the control of the OFDA-DNK system was obtained from the Rogowski coil (RB). Voltage information regarding the welding current has been obtained through the RB connected to the secondary of the welding transformer. Then, data transfer to analog-digital converter (ADC) was carried out with the help of the proposed integrator circuit. The performance of the proposed circuit has been tested in the established MFDC-RSW system. According to the experimental results, it has been seen that the proposed circuit can perform the voltage conversion up to 30 kA without error. In addition, it can also be said that the proposed circuit has the potential to send linear current measurement data to ADC in MFDC-RSW applications.
Anahtar Kelime:

Belge Türü: Makale Makale Türü: Araştırma Makalesi Erişim Türü: Erişime Açık
  • 1. Abdi-Jalebi, E., McMahon, R. (2005) Simple and practical construction of high-performance, low-cost Rogowski transducers and accompanying circuitry for research applications, IMTC 2005 - Instrumentation and Measurement Technology Conference, Ottawa, Canada, 354– 358.
  • 2. Altun, Y., Özcan, M. (2015) Ütü masası üretiminde kullanılan elektrik direnç nokta kaynak makinesi tasarım parametrelerinin tespiti, Mühendislik Bilimleri ve Tasarım Dergisi, 3 (2), 85-90.
  • 3. Azizoğlu, B.T, Karaca, H. (2017) Geniş bantlı akım algılayıcı için gerekli aktif entegratör devresi tasarım ve gerçeklemesi, Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi, 19(55), 45–51, doi: 10.21205/deufmd.2017195504
  • 4. Brydak K., Szlachta, A. (2016) Measuring methods of welding process parameters, Measurement Automation Monitoring, 62(1), 26–29.
  • 5. Deepati, A.K., Alhazmi, W., Benjeer, I. (2021) Mechanical characterization of AA5083 aluminum alloy welded using resistance spot welding for the lightweight automobile body fabrication, Materials Today: Proceedings, 1–10, doi: 10.1016/j.matpr.2021.01.646
  • 6. Duan, B., Zhang, C., Guo, M., Zhang, G. (2014) A new digital control system based on the double closed-loop for the full-bridge inverter, The International Journal of Advanced Manufacturing Technology, 77(1–4), 241–248, doi: 10.1007/s00170-014-6463-6
  • 7. Fiore, J.M. (2016) Operational amplifiers & linear integrated circuits: theory and application, Independently published, 1–589, ISBN13: 978–1796856897
  • 8. Giaccone, L., Cirimele, V., Canova, A. (2020) Mitigation solutions for the magnetic field produced by MFDC spot welding guns, IEEE Transactions on Electromagnetic Compatibility, 62(1), 83–92, doi: 10.1109/temc.2018.2877805
  • 9. Hofstötter, N., Krapp, J. (2018). Data sheet skyper 32pro r, Semikron, Erişim Adresi: https://www.semikron.com/dl/service-support/downloads/download/semikron-datasheetskyper-32-pro-r-l6100202.pdf, (Erişim Tarihi: 07.05.2021)
  • 10. Jenney, C.L., O’Brien, A. (2001) Welding handbook, Vol. 1: Welding Science and Technology (9th ed.), Woodhead Publishing Ltd., 1–985, ISBN–10: 0871716577
  • 11. Jun, Y., Li, G., Liu, H., Yang, G., Ling, G. (2016) Design of a flexible rogowski coil with active integrator applied in lightning current collection. 33rd International Conference on Lightning Protection (ICLP), 1–7, doi: 10.1109/iclp.2016.7791472
  • 12. Keller, P. (2013) Measuring magnetic field transients, Magn. Tech.Int., 57–60.
  • 13. Klopcic, B., Stumberger, G., & Dolinar, D. (2007) Iron core saturation of a welding transformer in a medium frequency resistance spot welding system caused by the asymmetric output rectifier characteristics, 2007 IEEE Industry Applications Annual Meeting, 2319– 2326, doi: 10.1109/07ias.2007.350
  • 14. Li, W., Feng, E., Cerjanec, D., Grzadzinski, G.A. (2004) Energy consumption in AC and MFDC resistance spot welding, Sheet Metal Welding Conference XI, Sterling Heights, MI, 1–12.
  • 15. Liu, Y., Lin, F., Zhang, Q., Zhong, H. (2011) Design and construction of a Rogowski coil for measuring wide pulsed current. IEEE Sensors Journal, 11(1), 123–130, doi: 10.1109/jsen.2010.2052034
  • 16. Lund, S.H.J., Billeschou, P., Larsen, L.B. (2019) High-bandwidth active impedance control of the proprioceptive actuator design in dynamic compliant robotics, Actuators, 8(4), 71–103, doi: 10.3390/act8040071
  • 17. Ramboz, J.D. (1995) Machinable Rogowski coil, design and calibration, Proceedings of 1995 IEEE Instrumentation and Measurement Technology Conference - IMTC ’95, 329–334, doi: 10.1109/imtc.1995.515151
  • 18. Ray, W.F., Hewson, C.R. (2000) High performance Rogowski coil current transducers, IEEE Industry Applications Conference, 5, 3083–3090.
  • 19. Rezaee, M., Heydari, H. (2010) Design modification of Rogowski coil for current measurement in low frequency, Iranian Journal of Electrical & Electronic Engineering, Vol. 6, No. 4, 232–238.
  • 20. Semikron (2013). Skm200gb12t4 Fast IGBT Module Data Sheet, Erişim Adresi: https://www.semikron.com/dl/service-support/downloads/download/semikron-datasheetskm200gb12t4-22892060.pdf (Erişim Tarihi: 07.05.2021)
  • 21. Tapashetti, P., Gupta, A., Mithlesh, C., Umesh, A.S. (2012) Design and simulation of op amp integrator and its applications, International Journal of Engineering and Advanced Technology (IJEAT), ISSN: 2249 – 8958, Volume-1, Issue-3, 12–19.
  • 22. Texas Instruments (2019). TMS320x2806x Technical Reference Manual, Erişim Adresi: https://www.ti.com/lit/ug/spruh18h/spruh18h.pdf, (Erişim Tarihi: 07.05.2021)
  • 23. Wang, X., Zhou, K., Shen, S. (2021) Intelligent parameters measurement of electrical structure of medium frequency DC resistance spot welding system, Measurement, 171, 108795–108806, doi: 10.1016/j.measurement.2020.108795
  • 24. Ward, D.A., Exon, J.L.T. (1993) Using Rogowski coils for transient current measurements, Engineering Science and Education Journal, 2(3), 105–113, doi: 10.1049/esej:19930034
  • 25. Xia, Y. J., Zhang, Z. D., Xia, Z. X., Zhu, S. L., & Zhang, R. (2015) A precision analogue integrator system for heavy current measurement in MFDC resistance spot welding, Measurement Science and Technology, 27(2), 025104–025114, doi: 10.1088/0957- 0233/27/2/025104
  • 26. Zhang, Y., Liu, J., Bai, G., & Feng, J. (2012) Analysis of damping resistor’s effects on pulse response of self-integrating Rogowski coil with magnetic core, Measurement, 45(5), 1277– 1285, doi: 10.1016/j.measurement.2012.01.009
  • 27. Zhou K., Cai, L. (2011) Improvement in control system for the medium frequency direct current resistance spot welding system, Proceedings of the 2011 American Control Conference, 2657–2663, doi: 10.1109/acc.2011.5990827
  • 28. Zhou, K., Li, H. (2020) A comparative study of single-phase AC and medium frequency DC resistance spot welding using finite element modeling, IEEE Access, 8, 107260–107271, doi: 10.1109/access.2020.3000794
  • 29. Zhou, K., Yao, P. (2017) Review of application of the electrical structure in resistance spot welding, IEEE Access, 5, 25741–25749, doi: 10.1109/access.2017.2771310
APA Özensoy C, UYAR M (2021). ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. , 401 - 420. 10.17482/uumfd.943314
Chicago Özensoy Can,UYAR Murat ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. (2021): 401 - 420. 10.17482/uumfd.943314
MLA Özensoy Can,UYAR Murat ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. , 2021, ss.401 - 420. 10.17482/uumfd.943314
AMA Özensoy C,UYAR M ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. . 2021; 401 - 420. 10.17482/uumfd.943314
Vancouver Özensoy C,UYAR M ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. . 2021; 401 - 420. 10.17482/uumfd.943314
IEEE Özensoy C,UYAR M "ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ." , ss.401 - 420, 2021. 10.17482/uumfd.943314
ISNAD Özensoy, Can - UYAR, Murat. "ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ". (2021), 401-420. https://doi.org/10.17482/uumfd.943314
APA Özensoy C, UYAR M (2021). ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi, 26(2), 401 - 420. 10.17482/uumfd.943314
Chicago Özensoy Can,UYAR Murat ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi 26, no.2 (2021): 401 - 420. 10.17482/uumfd.943314
MLA Özensoy Can,UYAR Murat ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi, vol.26, no.2, 2021, ss.401 - 420. 10.17482/uumfd.943314
AMA Özensoy C,UYAR M ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi. 2021; 26(2): 401 - 420. 10.17482/uumfd.943314
Vancouver Özensoy C,UYAR M ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi. 2021; 26(2): 401 - 420. 10.17482/uumfd.943314
IEEE Özensoy C,UYAR M "ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ." Uludağ Üniversitesi Mühendislik Fakültesi Dergisi, 26, ss.401 - 420, 2021. 10.17482/uumfd.943314
ISNAD Özensoy, Can - UYAR, Murat. "ORTA FREKANS DOĞRU AKIM DİRENÇ NOKTA KAYNAK SİSTEMLERİ İÇİN AKIM ÖLÇÜM DEVRESİ TASARIMI VE GERÇEKLENMESİ". Uludağ Üniversitesi Mühendislik Fakültesi Dergisi 26/2 (2021), 401-420. https://doi.org/10.17482/uumfd.943314